Question 1

What are the main welding processes and when do I use each?

Accepted Answer

MIG (Gas Metal Arc Welding): fast, good for thick and thin metals, semi-automatic (gun feeds wire), great for production. TIG (Gas Tungsten Arc Welding): slower, premium quality, used for thin/exotic metals (aluminum, titanium), full manual control (foot pedal or lever). Stick (Shielded Metal Arc Welding): portable, works outdoors and in windy conditions (shielding gas from electrode coating, not external tank), good for field work and structural. Plasma: cuts through metal at high speed, used for cutting blanks. For a job shop: MIG for general purpose, TIG for precision/thin work, stick for field repairs. For aerospace: TIG or electron-beam welding (vacuum). Pressure equipment: must use code-approved processes (AWS D1.1 qualified).

Question 2

What is a welding symbol and how do I read it?

Accepted Answer

A welding symbol is a blueprint shorthand showing the location, type, and size of a weld. The symbol sits on a reference line (the joint). A triangle = fillet weld (two surfaces meeting at 90 degrees); a square = butt weld (two surfaces end-to-end); a circle around the corner = all-around weld; an arrow points to the joint. Numbers near the symbol show bead size (leg size for fillet, depth for butt) and length. AWS has standardized symbols; once you learn the basic dozen, reading symbols is fast. A welder who misreads a symbol might weld the wrong joint or use the wrong size fillet, causing joint failure or wasting time re-welding.

Question 3

What is penetration and why is it critical?

Accepted Answer

Penetration is how deep the weld metal melts into the base metal, forming a strong fusion. Full penetration means the weld completely fills the joint from one side to the other (critical for pressure vessels, bridges); partial penetration is acceptable for non-critical joints (structural bolted connections, brackets). Under-penetration (the weld sits on the surface without fusing properly) creates a weak joint that can fail under load. Over-penetration (weld burns through the back side, creating porosity or distortion) is wasteful and, in pressure equipment, violates code. A welder achieves proper penetration by: controlling travel speed (too fast and you don't fuse deeply), heat input (amperage and voltage), and technique (angle, puddle position). Radiographic inspection (X-ray) is the way to verify penetration on critical welds.

Question 4

What causes porosity, cracking, and undercuts in welds?

Accepted Answer

Porosity (gas bubbles trapped in the weld): usually hydrogen from moisture in electrodes or shielding gas. Fix: bake electrodes to remove moisture, check gas tank purity, and ensure proper arc length. Cracking (cold cracks or hot cracks in the weld bead): from rapid cooling, high restraint (thick base metal, complex geometry), or poor technique. Fix: preheat the part (especially thick steel), use slower travel speed (more heat input), control cooling (insulate until cool), and use low-hydrogen electrodes. Undercuts (a groove melted into the base metal at the toe of the weld): from too much heat or slow travel. Fix: reduce travel speed, reduce amperage, or use multiple passes instead of one heavy pass. All three defects require re-welding (grinding out, re-doing the joint). Code-critical welds are UT (ultrasonic) or radiographically inspected to ensure zero defects.

Question 5

How do I qualify for AWS D1.1 certification?

Accepted Answer

AWS D1.1 (Structural Steel Code) certification proves you can weld structural joints to code standard. You must pass a practical test: weld a sample joint (typically a butt weld in a T-joint or corner joint) in the position specified (flat, horizontal, vertical, overhead), then have it inspected radiographically and mechanically tested (bend test under load to ensure the weld doesn't crack). If you pass, you're qualified for that position and process. Positions limit where you can work: 1G (flat) is easiest and fastest; 4G (overhead) is hardest and what's required for most structural work. Certification lasts three years; you must renew by re-testing or by demonstrating continuous welding work.

Question 6

What is the difference between tack welds and finish welds?

Accepted Answer

Tack welds are small, temporary welds used to hold parts in position while you do the final (finish) weld. Tack welds are quick and loose; you deliberately weld over them during the finish pass (they dissolve into the final weld). If you skip tack welds on a complex assembly, parts can shift mid-weld and the final geometry is wrong. Tack welding is an art: you need just enough tack to hold position without excess heat that warps the part. For a multi-pass (stacked) weld, you usually tack at multiple points around the perimeter, then start the finish pass on one side and work your way around.

Question 7

What is shielding gas and why does it matter?

Accepted Answer

Shielding gas is the gas (typically argon, CO2, or a mixture) that keeps oxygen and nitrogen in the air from contaminating the weld pool. Different processes use different gases: MIG uses an external tank of shielding gas (you choose the mixture), TIG uses argon or argon-helium mix, stick uses nothing (the electrode coating provides shielding). Gas quality matters: contaminated gas (moisture, nitrogen) causes porosity and weak welds. Operators check: tank pressure (adequate supply), regulator (keeps pressure steady), and flow meter (typically 15-25 CFM for MIG). A leak in the hose or connection starves the arc of shielding, causing spatter and porosity. Regular inspection of gas lines is part of preventive maintenance.

অঞ্চল	জুনিয়র	মধ্য	সিনিয়র
USA	$38k	$52k	$72k
UK	£24k	£33k	£46k
EU	€28k	€38k	€54k
CANADA	C$43k	C$60k	C$82k

অঞ্চল	জুনিয়র	মধ্য	সিনিয়র
USA	$38k	$52k	$72k
UK	£24k	£33k	£46k
EU	€28k	€38k	€54k
CANADA	C$43k	C$60k	C$82k

Welding and Metal Fabrication